INPUTS AND OUTPUTS:
¾Voltage to the flame detection probe: max 300 Vac
¾Minimum ionization current: 2,4 µA ± 0,3 µA
¾Current limits to the probe: 1 mA
¾Flame signal display: 0 ÷ 90 µA
¾Detection probe type: electrode or scanner ESA UV-2
¾Probe line length to electrode or UV-2 detection: < 30 m
¾Insulation between the probe conductors: > 50 MΩ (cables with double insulation or double protection)
¾HV cable length from ignition transformer: maximum 2 m
¾Distance between ignition electrode and burner mass: 3 mm ± 0,5
¾Digital input voltage: the same as the supply voltage
¾Digital input absorption: max 5mA
¾Filter for digital input: RC 100 Ω - 0,47 µF - 250 Vac
¾Digital output and ignition transformer voltage: the same as the supply voltage
¾Maximum current per single output in voltage: 1,5 A (2 A for ignition transformer)
¾Fuel valve output (MODE 1,3,4): free voltage safe SPST contact
¾Maximum current and voltage for fuel valve output (MODE 1,3,4) : 1,5A, 24÷230 Vac, 24÷48 Vdc
¾Flame detected safe output (MODE 2)*: free voltage safe SPDT contact
¾Maximum current and voltage for flame detected output (MODE 2) : 1,5A, 24÷230 Vac, 24÷48 Vdc
¾Status indication output: free voltage SPDT contact
¾Maximum current and voltage for indication output: 1,5A, 24÷230 Vac/Vdc
¾Outputs protection fuse: 3.15A rapid (**) replaceable
¾Flame detected or fuel valve output fuse: 3.15A rapid (**) replaceable
¾Internal relay protection fuse: 4 A not replaceable
¾Instrument protection fuse: 1 A not replaceable
¾Minimum voltage supply to maintain output: 70Vac (version 115Vac) and
140Vac (version 230Vac)
¾EXP-2, EXP-4 and EXP5 expansion card input voltage: 24 Vac/Vdc, 115 Vac, 230 Vac
¾EXP-2, EXP-4 and EXP5 expansion card input absorption: max 5mA
¾EXP-2, EXP-4 and EXP5 expansion card output voltage: the same as the supply voltage
¾EXP-2, EXP-4 and EXP5 expansion card output maximum current: 2A (not protected by internal fuse)
* NC contact safety output available only in mode 2
** On request it is possible to implement a fast fuse 4A.
PARAMETERS:
¾Purging or waiting time before ignition: 0 ÷ 99 sec or 2 ÷ 20 min
¾1st gas stage safety time*: 1 ÷ 25 sec
¾Regulation delay time*: 0 ÷ 25 sec
¾Reaction time*: 1 ÷ 20 sec
¾Shut off purging or waiting time: 0 ÷ 99 sec or 2 ÷ 4 min
¾Accepted remote unlocks: max 5 in 15 minutes
¾Flame sensor check on permanent operation: in 1 hour
¾Auto shut down for test with non permanent operation: in 24 hours
¾Behaviour at flame loss: configurable
¾1st gas stage burner functioning: configurable
¾Air valve functioning: configurable

E3001 Radiant cone flame burners RAD-65 & RAD-120
E3002 Metallic monoblock burners FC
E3004 Free flame medium velocity burners EMB
E3005 modular Infra-red burners BR-70
E3006 Infra-red burners for radiant panels SHELL-TEC
E3007 Monoblock free flame burners EPB
E3010 Ribbon linear flame burners AB & ABM
E3121 Pilot heads BTC & BTSA
E3160 High velocity premix burners E-THERM
E3201 Linear burners PYROLINE & MIDGET-PYROLINE
E3245 High blast torches HBT
E3280 Blast pilots PBC & PBST
E3319 LOW NOx radiant flame burners RAD-NxT
E3400 LOW NOx lateral burners ENM-NxT
E3400D LOW NOx Dual fuel lateral burners ENM-NxT-DF
E3500 Flat flame burners ESW
E3501 Long flame burners “Nozzle Mix” NM
E3502 Excess air burnes XNM
E3503 OUT OF PRODUCTION -Flat flame burners SW
E3504 Red-eye gas burners RE
E3505 OUT OF PRODUCTION – Hot shot high velocity burners HS
E3506 High velocity burners with flame tube in SiC EMB-SIK
E3507 Staged Air High velocity LOW NOx burners EMB-SIK-NxT
E3509 Double air high speed burners with SiC flame tube EMB-SIK-DA
E3512 Air shields AS
E3610 Dual fuel burners XDF
E3611 Dual fuel burners EXDF
E3615 Gas oil burners 12XDF
E3700 LOW NOx Air-Oxygen-fuel burner AGO-NxT
E3710 High Turbulence Oxy Fuel Burners HT
E3730 Oxygen-fuel burners with rotating flame TF
E3900 Staged Radiant tube burners RT
E3901FF OUT OF PRODUCTION Self-recuperative burners high speed free flame REKO-SIK-FF
E3901FN Self-recuperative burners high speed free flame REKO-SIK-NxT-FF
E3901RN Self-recuperative burners Low NOx for radiant tubes REKO-SIK-NxT-RT
E3901RT OUT OF PRODUCTION – Self-recuperative burners radiant tube REKO-SIK-RT
E3903 OUT OF PRODUCTION -Self-recuperative burners high speed with flat flame REKO-SIK-SW
E3903N Self-recuperative burners high speed with flat flame REKO-SIK-NxT-SW
E3905 Regenerative burners REGE-NxT
E3999 Elbows with peepsights for burners CR
E7000 Specification on how to choose and use flame sensor FLAME SENSOR
E7001 High sensibility probes UV-2
E7003 ESA UV-2 cheking device for permanent operation ESA SHUTTER SHR
E7014 Microprocessor operated burner control device ESA ESTRO
E7014P Permanent operation microprocessor burner control ESA ESTRO-PO
E7015 Serial gateway for ESA ESTRO and ESA REFLAM ESA BRIDGE & EXP-3
E7019 Thermoregulator and air/gas ratio regulator ESA TARC-II
E7021 Permanent operation microprocessor burner control device ESA GENIO-S
E7022 Permanent operation microprocessor burner control device ESA GENIO-PRS
E7061 Communication parameter programmer ESA PROG-1
E7081 Serial communication interface for ESA ESTRO ESA ECS-DRIVER
E7104 Serial converter for ESA ESTRO and ESA REFLAM ESA PLEX-COM1
E7105 Multizone serial for ESA ESTRO flame control ESA PLEX-STD
E7108 Pulse Firing controller for ESA ESTRO and ESA REFLAM ESA PLEX-PULSE
E7210 Flow rate and pressure transmitter ESA PT II
E7220 Portable differential pressure gauge ESA DPG-E
E7301 Electric servomotor ESA SERIO TPF
E7802 Burner control and flame detector for permanent and not-permanent operation ESA REFLAM-H