Cảm biến áp suất 113B28 | ICP Pressure Sensor PCB
ENGLISH: | SI: | ||
---|---|---|---|
PERFORMANCE | |||
Measurement Range (for ±5V output) | 50 psi | 344.7 kPa | |
Useful Overrange (for ± 10V output) | 100 psi | 689.4 kPa | [ 3] |
Sensitivity (±15 %) | 100 mV/psi | 14.5 mV/kPa | |
Maximum Pressure | 1000 psi | 6895 kPa | |
Resolution | 0.001 psi | 0.007 kPa | [ 2] |
Resonant Frequency | ≥500 kHz | ≥500 kHz | |
Rise Time | ≤1.0 µ sec | ≤1.0 µ sec | |
Low Frequency Response (-5 %) | 0.5 Hz | 0.5 Hz | |
Non-Linearity | ≤1.0 % FS | ≤1.0 % FS | [ 1] |
ENVIRONMENTAL | |||
Acceleration Sensitivity | ≤0.002 psi/g | ≤0.0014 kPa/(m/s²) | |
Temperature Range (Operating) | -100 to +275 °F | -73 to +135 °C | |
Temperature Coefficient of Sensitivity | ≤0.03 %/°F | ≤0.054 %/°C | |
Maximum Flash Temperature | 3000 °F | 1649 °C | |
Maximum Vibration | 2000 g pk | 19614 m/s² pk | |
Maximum Shock | 20000 g pk | 196140 m/s² pk | |
ELECTRICAL | |||
Discharge Time Constant (at room temp) | ≥1.0 sec | ≥1.0 sec | |
Excitation Voltage | 22 to 30 VDC | 22 to 30 VDC | |
Constant Current Excitation | 2 to 20 mA | 2 to 20 mA | |
Output Impedance | <100 Ohm | <100 Ohm | |
Output Bias Voltage | 8 to 15 VDC | 8 to 15 VDC | |
PHYSICAL | |||
Sensing Geometry | Compression | Compression | |
Sensing Element | Quartz | Quartz | |
Housing Material | 17-4 Stainless Steel | 17-4 Stainless Steel | |
Diaphragm | Invar | Invar | |
Sealing | Welded Hermetic | Welded Hermetic | |
Electrical Connector | 10-32 Coaxial Jack | 10-32 Coaxial Jack | |
Weight (with clamp nut) | 0.16 oz | 4.5 gm |
* All specifications are at room temperature unless otherwise specified
.
[ 1] Zero-based, least-squares, straight line method.
[ 2] Typical.
[ 3] For +10 volt output, minimum 26 VDC supply voltage required. Negative 10 volt output may be limited by output bias.
[ 4] See PCB Declaration of Conformance PS023 for details.
Supplied | ||
060A03 | Clamp nut, 5/16-24-2A thd, 1/4" hex, SS (for Series 111, 112 & 113) | 1 |
060A05 | Clamp nut, M7 x 0.75-6G thd (for Series M111, M112 & M113) | 1 |
065A05 | Seal sleeve, sensor recess mount, 0.248" OD x 0.221" ID x 0.240" thk, 17-4 SS (for Series 111A, 112A & 113A) | 1 |
065A02 | Seal ring, sensor flush mount, 0.248" OD x 0.219" ID x 0.015" thk, brass (for Series 111A, 112A & 113A) | 3 |