Cảm biến lực Force Sensor 200C20 PCB
[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] Calculated from discharge time constant.
[4] Estimated using rigid body dynamics calculations.
[2] Typical.
[5] Minimum 25 VDC required for maximum output voltage.
[2] Typical.
[6] See PCB Declaration of Conformance PS023 for details.
ENGLISH: | SI: | ||
---|---|---|---|
PERFORMANCE | |||
Sensitivity (±15 %) | 0.25 mV/lb | 56.2 mV/kN | |
Measurement Range (Compression) | 20000 lb | 88.96 kN | |
Maximum Static Force (Compression) | 30000 lb | 133.44 kN | |
Broadband Resolution (1) | 0.30 lb-rms | 1.3 N-rms | [2] |
Low Frequency Response (-5 %) | 0.0003 Hz | 0.0003 Hz | [3] |
Upper Frequency Limit | 40000 Hz | 40000 Hz | [4] |
Non-Linearity | ≤1 % FS | ≤1 % FS | [1] |
ENVIRONMENTAL | |||
Temperature Range | -65 to +250 °F | -54 to +121 °C | |
Temperature Coefficient of Sensitivity | ≤0.08 %/°F | ≤0.144 %/°C | |
ELECTRICAL | |||
Discharge Time Constant (at room temp) | ≥2000 sec | ≥2000 sec | |
Excitation Voltage | 20 to 30 VDC | 20 to 30 VDC | [5] |
Constant Current Excitation | 2 to 20 mA | 2 to 20 mA | |
Output Impedance | ≤100 Ohm | ≤100 Ohm | |
Output Bias Voltage | 8 to 14 VDC | 8 to 14 VDC | |
Spectral Noise (1 Hz) | 0.039 lb/√Hz | 0.17 N/√Hz | [2] |
Spectral Noise (10 Hz) | 0.012 lb/√Hz | 0.054 N√Hz | [2] |
Spectral Noise (100 Hz) | 0.0034 lb/√Hz | 0.015 N/√Hz | [2] |
Spectral Noise (1000 Hz) | 0.00088 lb/√Hz | 0.0039 N/√Hz | [2] |
Output Polarity (Compression) | Positive | Positive | |
PHYSICAL | |||
Stiffness | 63 lb/µin | 11 kN/µm | [2] |
Size - Diameter | 1.5 in | 38.1 mm | |
Size - Height | 0.5 in | 12.7 mm | |
Weight | 3.1 oz | 88 gm | |
Housing Material | Stainless Steel | Stainless Steel | |
Sealing | Hermetic | Hermetic | |
Electrical Connector | 10-32 Coaxial Jack | 10-32 Coaxial Jack | |
Electrical Connection Position | Side | Side | |
Mounting Thread | 1/4-28 Female | Not Applicable |
* All specifications are at room temperature unless otherwise specified.
Supplied | ||
080A81 | Thread lock adhesive (for Series 200) | 1 |
081A06 | Mounting stud, 1/4-28 to 1/4-28 thds x 0.365", no shoulder | 1 |
081B20 | Mounting stud, 1/4-28 to 1/4-28 x 0.365" long, BeCu w/shoulder | 1 |
084B23 | Impact cap, convex (for Model 200C20) | 1 |
M081A61 | Mounting stud, 1/4-28 to M6x1 x 8.6 mm long, BeCu w/shoulder | 1 |