Cảm biến lực Force Sensor 260A01 260A02 260A03 PCB
[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] Sensitivites are for listed preload. Sensitivites may vary ±5% depending on preload used.
[4] Sensitivities are dependent upon supplied bolt.
[2] Typical.
[5] Preload should be at least 10 times the X and Y operating range used.
[6] See PCB Declaration of Conformance PS023 for details.
ENGLISH: | SI: | ||
---|---|---|---|
PERFORMANCE | |||
Sensitivity (±20 %) (Z Axis) | 2.5 mV/lb | 0.56 mV/N | [3] [4] |
Sensitivity (±20 %) (X or Y Axis) | 10 mV/lb | 2.25 mV/N | [3] [4] |
Measurement Range (Z Axis) | 1000 lb | 4.45 kN | |
Measurement Range (X or Y Axis) | 500 lb | 2.22 kN | |
Maximum Force (Z Axis) | 1320 lb | 5.87 kN | |
Maximum Force (X or Y Axis) | 660 lb | 2.94 kN | |
Maximum Moment (Z Axis) | 14 ft-lb | 18.98 Nm | |
Maximum Moment (X or Y Axis) | 13 ft-lb | 17.63 Nm | |
Broadband Resolution (z axis) | 0.006 lb-rms | 0.027 N-rms | [2] |
Broadband Resolution (x or y axis) | 0.002 lb-rms | 0.0089 N-rms | [2] |
Upper Frequency Limit | 90 kHz | 90 kHz | |
Low Frequency Response (-5 %) (Z-Axis) | 0.01 Hz | 0.01 Hz | |
Low Frequency Response (-5 %) (X or Y axis) | 0.001 Hz | 0.001 Hz | |
Non-Linearity | ≤1 % FS | ≤1 % FS | [1] |
Cross Talk (between X and Y Axis) | ±3 % | ±3 % | |
Cross Talk (between (X or Y axis) and Z Axis) | ±5 % | ±5 % | |
ENVIRONMENTAL | |||
Temperature Range | -65 to +250 °F | -54 to +121 °C | |
ELECTRICAL | |||
Full Scale Output (Z Direction) | ±2.5 VDC | ±2.5 VDC | |
Full Scale Output (X and Y Direction) | ±5 VDC | ±5 VDC | |
Discharge Time Constant (Z axis) | ≥50 sec | ≥50 sec | |
Discharge Time Constant (X or Y axis) | ≥500 sec | ≥500 sec | |
Excitation Voltage (all channels) | 20 to 30 VDC | 20 to 30 VDC | |
Constant Current Excitation (all channels) | 2 to 20 mA | 2 to 20 mA | |
Output Impedance | ≤100 Ohm | ≤100 Ohm | |
Output Bias Voltage | 8 to 14 VDC | 8 to 14 VDC | |
Spectral Noise (1 Hz) | 0.0003 lb/√Hz | 0.00134 N/√Hz | |
Spectral Noise (10 Hz) | 0.00015 lb/√Hz | 0.000668 N/√Hz | |
Spectral Noise (100 Hz) | 0.00005 lb/√Hz | 0.000223 N/√Hz | |
Spectral Noise (1000 Hz) | 0.000015 lb/√Hz | 0.0000668 N/√Hz | |
Spectral Noise (1 Hz) | 0.0015 lb/√Hz | 0.00668 N/√Hz | |
Spectral Noise (10 Hz) | 0.00055 lb/√Hz | 0.00245 N/√Hz | |
Spectral Noise (100 Hz) | 0.0002 lb/√Hz | 0.000891 N/√Hz | |
Spectral Noise (1000 Hz) | 0.000055 lb/√Hz | 0.000245 N/√Hz | |
Output Polarity | Positive | Positive | |
PHYSICAL | |||
Preload | 5000 lb | 22.25 kN | [5] |
Stiffness (Z Axis) | 10 lb/µin | 1.75 kN/µm | [2] |
Stiffness (X or Y Axis) | 4 lb/µin | 0.7 kN/µm | [2] |
Size - Height | 0.390 in | 9.90 mm | |
Size - Length | 1.075 in | 27.3 mm | |
Size - Width | 0.95 in | 24.1 mm | |
Size - Bolt Diameter | 0.205 in | 5.21 mm | |
Size - ID | 0.319 in | 8.10 mm | |
Size - Sensing Surface | 0.680 in | 17.27 mm | |
Weight | 0.927 oz | 26.27 gm | |
Housing Material | Stainless Steel | Stainless Steel | |
Sealing | Hermetic | Hermetic | |
Electrical Connector | 4-Pin | 4-Pin | |
Electrical Connection Position | Side | Side |
* All specifications are at room temperature unless otherwise specified.
Supplied | ||
081A70 | Pre-load bolt (for Models 260A01, 260A11, & 260A31) | 1 |
082B02 | Anti-friction washer for Models (M)202B, (M)212B, (M)260A01, (M)260A11 & (M)260A31 | 1 |
083A10 | Pilot bushing (for Models 260A01, 260A11 & 260A31) | 1 |
M081A70 | Pre-load bolt (for Models 260A01, 260A11 & 260A31) | 1 |
(W) Water Resistant Cable
ENGLISH | SI | |
---|---|---|
Electrical Connection Position | Side |